|
|
| • | Chuck converts SDS-Plus rotary hammer to 1/2" 3 jaw chuckAccepts all 1/2" straight shank drill bits |
|
$43.40
|
|
|
|
|
| • | With tapping units installed, the Slugger JM101, USA5 and 4x4 are converted into full production tapping machines in minutes, utilizing taps from #10 to 3/4". |
|
$925.00
|
|
|
|
|
| • | With tapping units installed, the Slugger JM101, USA5 and 4x4 are converted into full production tapping machines in minutes, utilizing taps from #10 to 3/4". |
|
$924.97
|
|
|
|
|
| • | Convert Slugger drilling machines into portable drill presses in seconds. Ideal for small and blind hole applications |
| • | *3/8" maximum drill bit can be used in this... |
|
$98.00
|
|
|
|
|
| • | This adapter is for using bits smaller than 7/16 of inch for the Jancy Holemaker |
| • | Clearance from chuck tip to magnet base is approx. 3" |
|
$99.97
|
|
|
|
|
| • | 3/4 chuck and adapter for USA5 and JM5000 |
|
$110.97
|
|
|
|
|
| • | See manufacturer Info Tab |
|
$175.00
|
|
|
|
|
| • | This adapter is for using bits smaller than 7/16 of inch for the Jancy JM101 |
|
$95.00
|
|
|
|
|
| • | Low cost with increased hole drilling productivity. |
| • | Drills up to three times faster than twist drills. |
|
$22.00
|
|
|
|
|
| • | Low cost with increased hole drilling productivity. Drills up to three times faster than twist drills. Produces accurate holes without pilot drillin... |
|
$45.00
|
|
|
|
|
| • | See Manufacturer Info Tab |
|
$135.00
|
|
|
|
|
| • | See Manufacturer Info Tab |
|
$120.00
|
|
|
|
|
| • | See Manufacturer Info Tab |
|
$130.00
|
|
|
|
|
| • | See Manufacturer Info Tab |
|
$120.00
|
|
|
|
|
| • | See Manufacturer Info Tab |
|
$185.00
|
|
|
|
|
| • | See Manufacturer Info Tab |
|
$135.00
|
|
|
|
|
| • | Extends the reach of slugger cutters in drilling applications, consult the factory for appliation information. |
|
$139.00
|
|
|
|
|
| • | Extends the reach of slugger cutters in drilling applications, consult the factory for appliation information. |
|
$164.00
|
|
|
|
|
| • | Extends the reach of slugger cutters in drilling applications, consult the factory for appliation information. |
|
$164.00
|
|
|
|
|
| • | 6" arbor extension, 1-5/16" arbor body diameter |
|
$325.00
|
|
|
|
|
|
$44.97
|
|
|
|
|
|
$79.97
|
|
|
|
|
| • | Threaded drive CT cutters |
| • | All arbors are #3MT |
|
$120.00
|
|
|
|
|
| • | Threaded drive CT cutters |
| • | All arbors are #3MT |
|
$120.00
|
|
|
|
|
| • | Threaded drive CT cutters |
| • | All arbors are #3MT |
|
$140.00
|
|
|
|
|
| • | Threaded drive CT cutters |
| • | All arbors are #3MT |
|
$120.00
|
|
|
|
|
| • | Threaded drive CT cutters |
| • | All arbors are #3MT |
|
$120.00
|
|
|
|
|
| • | Threaded drive CT cutters |
| • | All arbors are #3MT |
|
$140.00
|
|
|
|
|
| • | Threaded drive CT cutters |
| • | All arbors are #3MT |
|
$120.00
|
|
|
|
|
| • | Threaded drive CT cutters |
| • | All arbors are #3MT |
|
$120.00
|
|
|
|
|
| • | Threaded drive CT cutters |
| • | All arbors are #3MT |
|
$140.00
|
|
|
|
|
| • | Threaded drive CT cutters |
| • | All arbors are #3MT |
|
$120.00
|
|
|
|
|
| • | Threaded drive CT cutters |
| • | All arbors are #3MT |
|
$120.00
|
|
|
|
|
| • | Threaded drive CT cutters |
| • | All arbors are #3MT |
|
$140.00
|
|
|
|
|
| • | See Manufacturer Info Tab |
|
$160.00
|
|
|
|
|
| • | See Manufacturer Info Tab |
|
$160.00
|
|
|
|
|
| • | See Manufacturer Info Tab |
|
$170.00
|
|
|
|
|
| • | See Manufacturer Info Tab |
|
$175.00
|
|
|
|
|
| • | Give all Jancy magnetic drills the ability to produce a precision chamfer in pre-existing holes. All countersinks are 82º. |
| • | Can use a countersink with a shop dril... |
|
$37.50
|
|
|
|
|
| • | Give all Jancy magnetic drills the ability to produce a precision chamfer in pre-existing holes. All countersinks are 82º. |
| • | Can use a countersink with a shop dril... |
|
$49.50
|
|
|